SANSICO INDUSTRIES SDN BHD+603 7859 7299 ally@sansico.com.my
 stancer@sansico.com.my
  • Home
    • About Us
  • Products
  • Project Gallery
  • Downloads
    • Catalogue
    • Certification
  • Distributors
    • Fittings & Pipe
    • Floor Trap
  • Contact Us

Hansen Fittings & Pipes

Home > Products > Hansen Fittings & Pipes


Product
Description
Technical Data
Benefits
Installation Method

Approved by the Water Supply (Water Quality) Regulations 1989 & Water Regulations Advisory Committee (WRAS) of UK for its use in potable water, this material is superior to existing materials being used in terms of strength and ability to withstand heat. The fittings are designed and comply to Sirim 11:2017.

MECHANICAL PROPERTIES

Hansen fittings, together with high density polyethylene (HDPE) pipes, provide an unsurpassable potable water system. These sleek fittings are slim enough to be buried in walls and are able to withstand very high pressures.

Mechanical Properties

Test Conditions

Units

Standards

Nylon 6

Tensile Modulus

1 mm/min

MPa

ISO 527

3600

Tensile Strain at break

5 mm/min

MPa

ISO 527

75

Tensile Strain at break

5 mm/min

%

ISO 527

12

Flexural Modulus

2 mm/min

MPa

ISO 178

3100

Flexural Strength

5 mm/min

MPa

ISO 178

120

Temperature of Deflection under load method Af

MPa

°C

ISO 75

190

Coefficient of Linear Thermal Expansion

23 to 55 °C

10-4 / K

ASTM E 831

0.3

Water Absorption

Saturation Value in water at 23 °C

%

ISO 62

8.5

Density

 

gm / cm3

ISO 1183

1.23



 

Resistance to pull out the assembled joint

The joined assembly is applied at a constant tension for 1 hour and complies with ISO 3501.

Hydrostatic pressure test

The fitting body shall withstand leakage for 1 hour an internal positive pressure of 4 times its maximum sustained working pressure which is 64 Bar. The fitting joint with HDPE pipe shall withstand without leakage for 1 hour an internal positive pressure of 24 bar, 1.5 times its maximum sustained working pressure.

Hydrostatic requirement when subjected to bending stress

When the assembly is bent to a radius of 20 times the diameter of the pipe, the joined assembly shall withstand for 1 hour without leakage an internal positive prssure of 24bar.

External pressure requirement

The joined assembly shall withstand for 1 hour without leakage, a pressure of 0.80 bar above atmospheric pressure.

Effect on water

complies to MS1583; supply of water intended for human consumption.

Opacity

the wall of the fittings shall not transmit mre than 0.2% of the visible light falling on it.

Approved by the Water Supply (Water Quality) Regulations 1989 & Water Regulations Advisory Committee (WRAS) of UK for its use in potable water, this material is superior to existing materials being used in terms of strength and ability to withstand heat. The fittings are designed and comply to Sirim 11:2017.

MECHANICAL PROPERTIES

Hansen fittings, together with high density polyethylene (HDPE) pipes, provide an unsurpassable potable water system. These sleek fittings are slim enough to be buried in walls and are able to withstand very high pressures.

Mechanical Properties

Test Conditions

Units

Standards

Nylon 6

Tensile Modulus

1 mm/min

MPa

ISO 527

3600

Tensile Strain at break

5 mm/min

MPa

ISO 527

75

Tensile Strain at break

5 mm/min

%

ISO 527

12

Flexural Modulus

2 mm/min

MPa

ISO 178

3100

Flexural Strength

5 mm/min

MPa

ISO 178

120

Temperature of Deflection under load method Af

MPa

°C

ISO 75

190

Coefficient of Linear Thermal Expansion

23 to 55 °C

10-4 / K

ASTM E 831

0.3

Water Absorption

Saturation Value in water at 23 °C

%

ISO 62

8.5

Density

 

gm / cm3

ISO 1183

1.23



 

Resistance to pull out the assembled joint

The joined assembly is applied at a constant tension for 1 hour and complies with ISO 3501.

Hydrostatic pressure test

The fitting body shall withstand leakage for 1 hour an internal positive pressure of 4 times its maximum sustained working pressure which is 64 Bar. The fitting joint with HDPE pipe shall withstand without leakage for 1 hour an internal positive pressure of 24 bar, 1.5 times its maximum sustained working pressure.

Hydrostatic requirement when subjected to bending stress

When the assembly is bent to a radius of 20 times the diameter of the pipe, the joined assembly shall withstand for 1 hour without leakage an internal positive prssure of 24bar.

External pressure requirement

The joined assembly shall withstand for 1 hour without leakage, a pressure of 0.80 bar above atmospheric pressure.

Effect on water

complies to MS1583; supply of water intended for human consumption.

Opacity

the wall of the fittings shall not transmit mre than 0.2% of the visible light falling on it.

BENEFITS OF HANSEN FITTING


  1. Size - Sleek joint system for use in confined areas or locations susceptible to ground movement and small enough to conceal in the wall.
  2. Time - Fast & simple installation.
  3. Simple - No "O" ring, No crimping, No solvent cement, No compression ring. No specialist / site equipment / skilled labour required.
  4. Cost effective - Saving in tools, workers and time.
  5. Durable - Long life service, leak-free. High performance material - Nylon 6 Engineering Plastic that can withstand heat & high stress applications.
  6. Price - Economical.
  7. Excellent hydraulic flow characteristics.
  8. Corrosion and rust resistance.
  9. Excellent hydraulic flow characteristics.
  10. Test results from reputed testing bodies; SIRIM, IKRAM, SPAN.

 

Cut the polypipe square with pipe cutters,
knife or saw to the required length.
Push fittings into the pipe as far as possible.
   
Wind the nut onto pipe a few turns.
Tighten with spanner or stillson.
Simply the best. No heat, crimpling or
solvent cement required.
Leak proof. Nothing to lose.
   

Equal Coupling
Reducing Coupling
Equal Elbow
Reducing Elbow
45˚ Equal Elbow
Equal Tee
Reducing Tee
Female Thread Adaptor
Female Thread Elbow
Female Brass Thread Elbow (BSPT Female)
Male Thread Adaptor
Tank Connector
Tee with Female Thread Branch
Male Tee with Female Branch
Male Cross Tee
Cross Tee
Bush
Extension Piece
Extension Piece Brass Threaded (BSPT Female & Male)
Equal Nipple
HDPE Pipe
View Enquiry

Categories

  • Hansen Fittings & Pipes
  • PE Socket Fusion Fittings
  • PE-RT Fittings & Pipes
  • Floor Trap
  • Electrofusion Fittings & Pipes
  • Electrofusion Machine
Sansico Industries Sdn Bhd© 2021. All Rights Reserved
Web Design & SEO by V-Channel Sdn Bhd